VOLKSWAGEN GOLF IV

since 1997 of release

Repair and car operation



Foltsvagen Golf 4
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Cooling system
+ 4. Fuel system
+ 5. Exhaust system
+ 6. Ventilation and heating system
+ 7. Coupling
+ 8. Transmission
+ 9. Suspension brackets and power shafts
+ 10. Steering
+ 11. Wheels and tires
+ 12. Brake system
+ 13. Body
- 14. Electric equipment and electroschemes
   14.1. Filament lamps
   14.2. Electric chains
   + 14.3. Detection of not closed chain
   14.4. Safety locks
   - 14.5. Accumulator
      14.5.1. Rules of care of the accumulator
      14.5.2. Accumulator check
      14.5.3. Battery charging
      14.5.4. Accumulator removal
      14.5.5. Accumulator installation
      14.5.6. The remarks concerning the accumulator with ventilating caps
      14.5.7. Charging system
   + 14.6. Generator
   + 14.7. Starter
   14.8. Replacement of bulbs of external lighting
   14.9. Removal and installation of an additional signal of braking
   14.10. Replacement of bulbs of internal lighting
   + 14.11. Devices of external lighting
   + 14.12. Adjustment of light of headlights
   14.13. Removal and installation of a combination of devices
   14.14. Removal and installation of switches of a steering column
   14.15. Removal and installation of switches
   14.16. Removal and radio receiver installation
   14.17. Removal and installation of high-frequency loudspeakers
   14.18. Removal and installation of low-frequency loudspeakers
   14.19. Recommendations about phone installation
   14.20. Aerial
   14.21. Check of a heater of back glass
   + 14.22. Explanations to electric circuits
   + 14.23. Schemes of electric equipment of the VW Golf car since September, 1997.




14.5.5. Accumulator installation

GENERAL INFORMATION

Hose connection for a conclusion of gases from the accumulator, being formed at its work

The hose intended for removal of gases, being allocated at operation of the accumulator, is shown by an arrow.

Elements of fastening of the accumulator

1–basic arm;

2–basic plate;

3–bolt;

4–arm

PERFORMANCE ORDER

Prevention

At installation of the accumulator do not press a hose intended for removal of gases, being allocated at operation of the accumulator (see fig. Hose connection for a conclusion of gases from the accumulator, being formed at its work). In a hose of removal of gases there is a valve which protects the accumulator from return flash.


1. Establish one party of the accumulator on a basic arm (see fig. Elements of fastening of the accumulator).
2. At installation of the accumulator check, that the fixing ledge (1) in the basis of the accumulator was established in a groove of a basic arm (it is shown by an arrow).
3. From the second party fix the accumulator a fixing plate and screw it a bolt, having tightened it the moment of 20 Nanometers.
4. Check reliability of fastening of the accumulator, otherwise service life of the accumulator it can be considerable it is reduced.
5. Connect a wire tip to the positive plug of the accumulator and tighten a bolt of fastening of the plug the moment of 6 Nanometers. Establish the case of the holder of safety locks on the storage battery, thus the current-carrying strip should be established on a bolt of fastening of the positive plug of the accumulator.
6. Fix the case of the holder of safety locks on the case of the storage battery.
7. Screw a bolt of fastening of an electrowire plate on the positive plug of the accumulator.
8. Establish safety locks in the holder of safety locks.
9. Connect to the holder of safety locks the electric socket.
10. Connect a weight wire to the accumulator and tighten a bolt of fastening the moment of 6 Nanometers.
11. If in the car the radio receiver with a code is established, repeatedly reprogram it.
12. Establish time on hours.
13. Make active window regulators with an electric drive:
      – close outside the car through a door of the driver or a door of the forward passenger. Check, that glasses and doors were reliably closed;
      – repeatedly close the car a key, thus hold a key in a closed position of at least 1 second.
Prevention

If there is a defect of electric window regulators, illumination of buttons of management on a door will blink.