VOLKSWAGEN GOLF IV

since 1997 of release

Repair and car operation



Foltsvagen Golf 4
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Cooling system
+ 4. Fuel system
+ 5. Exhaust system
+ 6. Ventilation and heating system
+ 7. Coupling
+ 8. Transmission
+ 9. Suspension brackets and power shafts
+ 10. Steering
+ 11. Wheels and tires
+ 12. Brake system
+ 13. Body
- 14. Electric equipment and electroschemes
   14.1. Filament lamps
   14.2. Electric chains
   + 14.3. Detection of not closed chain
   14.4. Safety locks
   + 14.5. Accumulator
   + 14.6. Generator
   + 14.7. Starter
   14.8. Replacement of bulbs of external lighting
   14.9. Removal and installation of an additional signal of braking
   14.10. Replacement of bulbs of internal lighting
   + 14.11. Devices of external lighting
   + 14.12. Adjustment of light of headlights
   14.13. Removal and installation of a combination of devices
   14.14. Removal and installation of switches of a steering column
   14.15. Removal and installation of switches
   14.16. Removal and radio receiver installation
   14.17. Removal and installation of high-frequency loudspeakers
   14.18. Removal and installation of low-frequency loudspeakers
   14.19. Recommendations about phone installation
   14.20. Aerial
   14.21. Check of a heater of back glass
   + 14.22. Explanations to electric circuits
   + 14.23. Schemes of electric equipment of the VW Golf car since September, 1997.






14.15. Removal and installation of switches

GENERAL INFORMATION

Prevention

At a detachment of the accumulator contents of cells of memory, for example, a radio receiver code are erased. Without a code the manufacturer can connect a radio receiver again only.

Before removal of any switch remove a weight wire from the accumulator and repeatedly connect it to the accumulator only after switch installation.


LIGHTING SWITCH

PERFORMANCE ORDER
1. Establish the handle of management of the switch of lighting in situation 0.
2. Press the handle of the switch of lighting (arrow 1). In this situation turn it clockwise (arrow 2) and take the lighting switch from the dashboard (arrow 3).
3. Disconnect from the switch the electric socket.
4. Connect to the lighting switch the electric socket.
5. Insert the lighting switch into a dashboard nest, then press it (arrow 1) and at the same time turn clockwise (arrow 2). Both hooks of fixing of the switch thus fall.
6. Press the handle of the switch of lighting (arrow 3) before accurate fixing of the switch in the dashboard.

PROOF-READER OF LIGHT HEADLIGHTS / REGULATOR OF INTENSITY OF ILLUMINATION OF THE DASHBOARD

PERFORMANCE ORDER

Prevention

Not to scratch the dashboard at switch removal, stick with a sticky tape area round the switch.


1. Using an edge of a thin screw-driver, hook the case of the switch and take it from the dashboard.
2. At installation of the switch press it into the dashboard before accurate fixing.

SWITCHES OF WINDOW REGULATORS

Switches of window regulators on a door of the driver are executed in the form of the block. In the presence of malfunction it is necessary to replace all block.

PERFORMANCE ORDER
Door of the driver
1. Using an edge of a thin screw-driver, move an overlay of the internal handle of a door to a door.
2. Remove the door handle together with the control unit from internal furnish of a door.
3. Disconnect the electric socket.
4. Unscrew three screws and remove the control unit.
5. Installation is made in sequence, return to removal.
Door of the forward passenger / back doors
6. Remove an internal upholstery of a door.
7. Disconnect the electric socket from the switch of window regulators.
8. Press a lateral surface of the switch (And) and take it from a nest in the case (In) the internal handle of opening of a door.
9. Insert to a zashchelkivaniye the window regulator switch into a nest of the case of the internal handle of a door.
10. Further installation is made in sequence, return to removal.

SWITCH OF MANAGEMENT OF MIRRORS

PERFORMANCE ORDER
1. Remove a door upholstery.
2. Disconnect the electric socket from the switch.
3. Wring out outside lateral fastenings of the switch (And) and take it from the case.
4. Insert the switch into the case and fix it.
5. Further installation is made in sequence, return to removal.

SWITCH OF MANAGEMENT OF THE HATCH / LAMP OF INTERNAL LIGHTING

Switch of management of a hatch / lamp of internal lighting

1–rasseivatel;

2–screws;

3–switch case;

4–electric socket;

5–electric socket;

6–bulb;

7–plafond bulb;

And – the removal direction;

In – hooks

PERFORMANCE ORDER
1. Remove a rasseivatel. For this purpose insert a knife blade or other similar subject into a crack between the case and a rasseivatel and carefully hook a rasseivatel.
2. Unscrew the screws, fixing the switch.
3. Press the switch in the direction of an arrow (And) and remove its back part from hooks (In).
4. Disconnect electric sockets and remove the switch.
5. Installation is made in sequence, return to removal.

SWITCHES OF THE ALARM LIGHT SYSTEM, HEATERS OF BACK GLASS AND OTHERS

PERFORMANCE ORDER
1. Fastening of switches is carried out in the identical way.
2. Not to scratch the dashboard at switch removal, stick with a sticky tape area round the switch.
3. An edge of the thin screw-driver inserted under the switch, take the switch from a dashboard nest.

Prevention

The switch consists of the switch and switch case with a functional symbol. The switch is latched in the switch case. If the switch from the dashboard acted in film only, using flat-nose pliers, take the switch case from the dashboard.


4. Disconnect from the switch the electric socket.
5. At installation of the switch connect to it the electric socket and fix it a clamp.
6. Move the switch into a dashboard nest before its fixing.

SWITCH OF BLOCKING OF THE COVER TOPLIVOZALIVNA OF THE MOUTH

PERFORMANCE ORDER
1. Insert an edge of a thin screw-driver or a knife into the switch case, wring out and take the switch from the central console.
2. Disconnect from the switch the electric socket.
3. At installation of the switch connect to it the electric socket and fix a clamp.
4. Insert the switch into a nest of the central console to a clamp zashchelkivaniye.