VOLKSWAGEN GOLF IV

since 1997 of release

Repair and car operation



Foltsvagen Golf 4
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Cooling system
+ 4. Fuel system
+ 5. Exhaust system
+ 6. Ventilation and heating system
+ 7. Coupling
+ 8. Transmission
+ 9. Suspension brackets and power shafts
+ 10. Steering
+ 11. Wheels and tires
+ 12. Brake system
- 13. Body
   13.1. Care of a body
   13.2. Care of an upholstery and rugs
   13.3. Repair of insignificant damages of a body
   13.4. Repair of strong damages of a body
   13.5. Forward panel of a body
   13.6. Removal and installation of a front bumper
   13.7. Removal and installation of a rear bumper
   13.8. Removal and installation of a forward wing
   13.9. Removal and installation of facing of a niche of a forward wing
   13.10. Removal and installation of facing of a niche of a back wing
   + 13.11. Cowl
   + 13.12. Cowl lock
   13.13. Removal and front grille installation
   13.14. Removal and installation of a lateral overlay of a body
   + 13.15. Doors
   + 13.16. Hatch
   13.17. Gutter cleaning
   + 13.18. Mirrors
   + 13.19. Central console
   13.20. Removal and installation of the top furnish in space for feet of the driver
   13.21. Removal and installation of a ware box
   13.22. Removal and installation of a lateral covering of space for feet
   13.23. Removal and installation of overlays of thresholds
   13.24. Removal and installation of the bottom facing of the central rack
   13.25. Removal and installation of the right lateral covering of a luggage compartment
   13.26. Removal and installation of a covering of a floor of a luggage compartment
   13.27. Removal and installation of back furnish of a luggage compartment
   13.28. Removal and installation of a forward seat
   13.29. Lateral safety cushions
   13.30. Removal of a pillow of a back many-placed seat
   13.31. Removal and installation of a back of a back seat
   + 13.32. Stekloomyvateli and screen wipers
+ 14. Electric equipment and electroschemes





13.8. Removal and installation of a forward wing

GENERAL INFORMATION

Elements of fastening of a forward wing
1–forward wing;
2–bolts of 9 pieces;
3–spring holder of a nut;
4–consolidation;
5–arm

Distance between the top parts of forward wings and mutual situation between wings in the horizontal and vertical planes

 
and = 2 mm

Removal

PERFORMANCE ORDER
1. Remove a front bumper and a bumper beam.
2. Remove facing of a niche of a forward wing.
3. Remove the lateral repeater of turns.
4. Unscrew 9 bolts, fixing covered (2, see fig. Elements of fastening of a forward wing).

Prevention

In order to avoid damage of a paint and varnish covering wind with a sticky tape of a place nearby from screws of fastening of a wing.


5. The wing is established on a layer of protective mastic therefore for separation of a wing from a body soften protective mastic by means of the hair dryer.
6. The hair dryer put on a flat nozzle and, gradually warming up mastic, remove a wing.

Installation

PERFORMANCE ORDER
1. Before wing installation into place clear an interfaced surface and put zinc paste in places of fastening of a wing on a wheel niche and a forward rack. This paste is used as anticorrosive protection.
2. Establish a forward wing on the car, combine openings under bolts and screw up bolts of fastening of a wing.
3. At installation of a wing check, that gaps between a wing and a cowl, and also between a wing and a forward door were uniform on all length.
4. Establish facing of a niche of a forward wing.
5. Establish a beam of a bumper and a front bumper.