VOLKSWAGEN GOLF IV

since 1997 of release

Repair and car operation



Foltsvagen Golf 4
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Cooling system
+ 4. Fuel system
+ 5. Exhaust system
+ 6. Ventilation and heating system
+ 7. Coupling
- 8. Transmission
   - 8.1. Removal and transmission installation
      8.1.1. Engines 1,8/1,9/2,3-I
      8.1.2. Engines 1,4/1,6-I
   8.2. Removal and installation of an automatic transmission
   8.3. Gear shifting mechanism
   8.4. Removal and installation of the case of the lever of gear shifting
   + 8.5. Adjustment of cables of gear shifting
   8.6. Full automation
   + 8.7. Adjustment of draft of a cable of the lever of gear shifting
+ 9. Suspension brackets and power shafts
+ 10. Steering
+ 11. Wheels and tires
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment and electroschemes




8.1.2. Engines 1,4/1,6-I

GENERAL INFORMATION

Arrangement and the moments of a tightening of bolts of fastening of a transmission on models with the engine 1,4-I

And, In – an arrangement of aligning plugs
1
M 12 x 65
80 Nanometers
2
M 12 x 55
80 Nanometers
3
M 10 x 50
25 Nanometers
4
M 12 x 140
80 Nanometers
5, 6
M 12 x 65
80 Nanometers
7
M 7 x 12
10 Nanometers

Arrangement and the moments of a tightening of bolts of fastening of a transmission on models with the engine 1,6-I

And, In – an arrangement of aligning plugs
1
M 12 x 65
80 Nanometers
2
M 12 x 80
80 Nanometers
3
M 10 x 50
25 Nanometers
4
M 12 x 140
80 Nanometers
5
M 7 x 12
10 Nanometers

Arrangement and the moments of a tightening of bolts of fastening of a transmission on models with the diesel SDI engine

And, In – an arrangement of aligning plugs
1
M 12 x 65
80 Nanometers
2
M 12 x 80
80 Nanometers
3
M 10 x 50
25 Nanometers
4
M 12 x 140
80 Nanometers
5
M 7 x 12
10 Nanometers

Prevention

Operations on engine 1,4/1,6-I removal same, as well as for engines 1,8/1,9/2,3-I. The operations concerning engines 1,4/1,6-I are given in this section only.


PERFORMANCE ORDER
1. Support of the engine carry out the crane for the eyes fixed on a head of the block of cylinders and the block of cylinders.
2. Using a screw-driver edge as the lever, remove operative draft (1) with directing (2), then remove fixing ring (3) and the console lever (4), having pulled it up. Having turned clockwise draft (5) with a quencher of fluctuations, remove it from the console lever. Moving up draft with a quencher of fluctuations, take it from a support (6).
3. Using a screw-driver edge, disconnect long drafts of a control lever of a transmission from directing (arrows). Unscrew the handle of gear shifting (1) from a transmission. Unscrew bolts (2) and remove switching console (3) with connecting drafts and the gear shifting handle.
4. Take a hose of the working cylinder of coupling from clips.
5. Unscrew two bolts, couplings fixing the working cylinder. Remove the working cylinder of coupling and, without disconnecting from it a hose, fix on a body.

Boltovoye connection
Tightening moments
The engine to the holder
60 Nanometers + 90 °
Transmission to the holder
60 Nanometers + 90 °
The holder to a body
60 Nanometers + 90 °
Support to a transmission
40 Nanometers + 90 °
Support to a body
20 Nanometers + 90 °