VOLKSWAGEN GOLF IV

since 1997 of release

Repair and car operation



Foltsvagen Golf 4
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Cooling system
+ 4. Fuel system
+ 5. Exhaust system
+ 6. Ventilation and heating system
+ 7. Coupling
+ 8. Transmission
- 9. Suspension brackets and power shafts
   + 9.1. Forward suspension bracket
   - 9.2. Back suspension bracket
      9.2.1. Removal and shock-absorber and spring installation
      9.2.2. Shock-absorber check
      9.2.3. Shock-absorber utilization
+ 10. Steering
+ 11. Wheels and tires
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment and electroschemes



Как на голосование можно накрутить голоса в России



9.2. Back suspension bracket

GENERAL INFORMATION

Back suspension bracket of front-wheel cars

1–shock-absorber;
2–spring;
3–beam;
4–top support of a spring;
5–shock-absorber support;
6–buffer;
7–brake disk;
8–bearing;
9–stabilizer of the cross-section
stability;
10-rezinometallichesky support;
11-cables of the hand brake

Elements of a back suspension bracket of front-wheel cars

1–bolt of fastening of a wheel, 120 Nanometers;
2–the screw with crosswise the shlitsy;
3–brake disk;
4–dustproof cap. After everyone
it it is necessary to replace removals of a cap.
Only at installation of a new cap the correct consolidation is provided;
5–самоконтрящаяся denadtsatigranny
nut, 175 Nanometers. At installation it is necessary to use a new nut;
6–a wheel nave with the bearing;
7–bolt 60, Nanometer. At installation it is necessary to use a new bolt;
8–brake board;
9–an arm for cables of the hand brake;
10-cable of the hand brake;
11-самоконтрящаяся nut, 80 Nanometers. At installation it is necessary to use a new nut;
12-bolt, 75 Nanometers. At installation it is necessary to use a new bolt;
13-bolt, 80 Nanometers. At installation it is necessary to use a new bolt;
14-arm of a support of a back beam;
15-holder of a cable of the hand brake;
16-rezinometallichesky support;
17-back beam;
18-sensor of speed of rotation of a wheel;
19-a bolt with an internal shestigrannik, 8 Nanometers;
20-support;
21-spring;
22-top support of a spring;
23-bolt, 60 Nanometers. At installation it is necessary to use a new bolt;
24-bolt, 75 Nanometers. At installation it is necessary to use a new bolt;
25-shock-absorber;
26-nut. At installation it is necessary to use a new nut, a nut tightening the demanded moment make on the car standing on the earth and with one person on back sitting;
27-nave pin;
28-protective casing;
29-a bolt with an internal shestigrannik, 65 Nanometers. At installation it is necessary to use a new bolt;
30-brake support

Basic element of a back suspension bracket is the beam with the levers welded on it. Before a back beam the stabilizer which reduces car lists on turns is established. To a body the back beam fastens via rezinometallichesky plugs. For amortization of a back beam separately located springs and shock-absorbers are used. As a result of a separate arrangement of springs of a back suspension bracket the volume of a luggage compartment increased.


Prevention

On bearing elements of a back suspension bracket welding and leveling works are not admissible. At installation it is necessary to use new самоконтрящиеся nuts to replace bolts which have corrosion traces.