Foltsvagen Golf 4
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Cooling system
+ 4. Fuel system
+ 5. Exhaust system
+ 6. Ventilation and heating system
+ 7. Coupling
+ 8. Transmission
+ 9. Suspension brackets and power shafts
- 10. Steering
10.1. Removal and safety cushion installation
10.2. Removal and installation of a steering wheel
10.3. Removal and installation of a tip of steering draft
10.4. Main malfunctions of a suspension bracket and steering
+ 11. Wheels and tires
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment and electroschemes
|
Steering transfer
|
1–tip of cross-section steering draft;
2–nut, 50 Nanometers;
3–collar. At installation it is necessary to use a new collar;
4–protective cover;
5–collar. At installation it is necessary to use a new collar;
6–steering draft, 75 Nanometers;
7–a clip with rubber;
8–the submitting pipeline;
9–nut, 22 Nanometers;
10-a collar with a rubber support. At installation of a collar of the shooter on it should show on a forward part of the car;
|
11-thermoprotective sheet screen;
12-самоконтрящаяся nut, 45 Nanometers. At installation it is necessary to use a new nut;
13-arm;
14-bolt, 24 Nanometers;
15-consolidation;
16-hydraulic pipe;
17-hollow bolt of M 16х1,5, 45 Nanometers;
18-hollow bolt of M 14х1,5, 40 Nanometers;
19-sealing rings. At installation it is necessary to use new sealing rings;
20-steering transfer |
The pump of the amplifier of a steering with an arm (established in the lower part)
|
1–arm;
2–bolt, 25 nanometers;
3–hollow bolt, 30 Nanometers;
4–delivery pipeline;
5–sealing ring. At installation it is necessary
to use the new
sealing ring;
6–the soaking-up pipeline;
7–collar;
|
8–pump of the amplifier of a steering. Before installation fill in in the pump liquid for the amplifier of a steering. Fill in liquid in soaking-up branch pipe of the pump and turn a pump shaft by hand before emergence of liquid in a delivery branch pipe;
9–belt pulley;
10-a bolt with an internal shestigrannik, 25 Nanometers;
11-Poliklinovy belt;
12-mechanism of a tension of a poliklinovy belt |
The pump of the amplifier of a steering with an arm (established in the top part)
|
1–arm;
2–bolt, 25 Nanometers;
3–pump of the amplifier of the helmsman
managements;
4–sealing ring;
5–hollow bolt, 30 Nanometers;
6–delivery pipeline;
|
7–bolt, 22 Nanometers;
8–belt pulley;
9–a bolt with internal a shestigrannik, 25 Nanometers;
10-Poliklinovy belt;
11-mechanism of a tension of a poliklinovy belt |
Tips of steering drafts should not have люфта. In the presence of damages of their protective covers it is necessary to replace immediately. Replacement of tips of steering drafts can be made, without removing steering transfer.
Removal
| PERFORMANCE ORDER |
| 1. Weaken bolts of fastening of a forward wheel, then lift a forward part of the car and fix on supports. |
| 2. Remove a forward wheel. |
| 3. Unscrew a nut of fastening of a spherical tip of steering draft, thus a finger of the hinge hold from a provorachivaniye with a six-sided wrench. |
|
4. Screw together a nut till the end of a carving, but do not unscrew completely, thus it will serve as an emphasis for a stripper (1 – the electric socket of the sensor ABS, A – a stripper of spherical hinges). |
| 5. Disconnect the electric socket of the ABS sensor. |
| 6. Using a stripper of spherical hinges, take the spherical hinge of a tip of steering draft from a rotary fist. |
| 7. Unscrew a lock-nut 2 (see fig. Steering transfer), fixing steering draft in relation to a tip of steering draft. |
| 8. Unscrew a tip of steering draft from steering draft, thus count the quantity of turns made by a tip of steering draft. |
|
Installation
| PERFORMANCE ORDER |
| 1. Screw a tip of steering draft on steering draft on the same quantity of turns, as when unscrewing. |
| 2. Tighten a lock-nut 2 (see fig. Steering transfer) by hand. |
| 3. Insert the spherical hinge of a tip of steering draft into a rotary fist and fix its new самоконтрящейся a nut, having tightened it the moment of 45 Nanometers. At a tightening of a nut hold a hinge finger from a provorachivaniye a face six-sided key. |
| 4. Tighten a lock-nut the moment of 50 Nanometers. |
| 5. Connect the electric socket of the ABS sensor. |
| 6. Establish a wheel and fix it bolts. |
| 7. Lower the car on the earth and tighten bolts of fastening the moment of 120 Nanometers. |
| 8. Check and, if necessary, adjust corners of installation of wheels. |
|
|
|
